Equipment options:

FineFocus 800
FineFocus 800/TWIN

with direct torch connection, torch hose parcel up to 15 m length

FineFocus 800
FineFocus 800/TWIN

plasma torch connection via plasma ignition box and hose
parcel extension; range of action max. 55 m from power source

FineFocus 800 Robo

with special plasma torch for robot application

. Fine Focus-technique with Double-Straight-Effect for the
 technological use of both cutting edges, no waste

. Cutting with suction (dry-plasma cutting) or cutting under
  water (UWP)
. Metallurgically perfect cutting edges by XL-Life-Time System   
  for cutting of mild steel with oxygen; no aftertreatment for
  following welding operation necessary

. High reliability of plasma torches through a direct and
  extremely effective cooling of the beam generation system
  and the torch head

. Manual plasma cutting with powerful hand torch PB-S75 WH-1
  up to max. 80 mm thickness (material depending)

. Stepless adjustable cutting current between 80 A and
  300 A at 100 % duty cycle

. Plasma rectifier with 12-pulse circuit for an extremely smooth
  cutting current; high efficiency and power factor

. Excellent suitable für CNC-controlled application

. Contactless high-voltage ignition for start of pilot arc
  Direct pre-selection of plasma gases and plasma
  gas mixtures (O2, air, Ar/H2, Ar/H2/N2) for best cutting quality
  at different materials

. Compatible to all mechanically, optically or numerically
  controlled guiding systems, interface for signal
  exchange is incorporated

. Pre-selection of rate of current rise for a nozzle-saving process

. Preset control for pre-selection of cutting current and
  analogous displayfor cutting current and arc voltage

. Select-control for setting of cutting current from potentiometer
  of power source by remote control or CNC system
  (cutting table, robot, direct setting)

 

	Mains voltage (other voltages on request)	400 V; 3 phases; 50 Hz
	Fuse, slow	125 A
	Connecting power	83 kVA
	Protection class	IP 22
	Insulation class	F
	Open-circuit voltage	400 V
	Cutting current	80 A up 300 A stepless
	Cutting range (material depending)              ·  quality cut    ·  max. cut	50 mm 80 mm
	Piercing             ·  stationary    ·  running	25 mm 40 mm
	Plasma gases	Air, O2, Ar/H2/N2,  Ar/H2, Ar/N2, N2
	Ignition	High-voltage ignition
	Weight	566 kg
	Dimensions (L x W x H)	1320 x 844 x 1470 mm

For cutting with lower quality demands for the cutting result or
simple workpieces alsothe following standard torches are suitable.

Technical data of plasma machine torch with swirl gas

 

	Type	PB-S77 W
	Technological application	Dry cutting (under water also possible)
	Hose parcel lengths	1 m, 6 m, 10 m, 15 m
	Coolant flow	5.5 to 7 l/min
	Pilot arc current	22 A
	Cutting current	max. 300 A
	Cutting thickness	60 mm (with swirl-gas, 80 mm (without swirl gas)
	Clamping diameter	58 mm
	Ignition of main arc	Fully-automatic power increase at workpiece contact

Technical data of plasma machine torches without swirl gas

 

	Type	PB-S75 W PB-S75 W-1 PB-S75 W-1/O2
	Hose parcel lengths	1 m, 6 m, 10 m, 15 m
	Coolant flow	5.5 to 7 l/min
	Pilot arc current	22 A
	Cutting current	max. 300 A
	Cutting thickness	80 mm (material depending)
	Clamping diameter	53 mm 51 mm (as option)
	Ignition of main arc	Fully-automatic power increase at workpiece contact

Manual Plasma Cutting

For manual plasma cutting up to 80 mm thickness
(material depending) the plasma hand torch PB-S75 WH-1
for cutting with the plasma gases air, Ar/H₂ , Ar/H₂/N₂ and
Ar/N₂ can be used.
A plasma torch with extended handle is also available.

Technical data Plasma Hand Torch

 

	Type	PB-S75 WH-1
	Hose parcel lengths	6 m, 10 m, 15 m
	Cutting current	max. 300 A
	Cutting thickness, max.	80 mm (material depending)