Suitable for straight, profile and bevel cutting of up to 60°, cutting
in all positions, for piercing, for hole cutting, for gouging,
cutting without run-on cuts, piercing without run-on cuts.

Positive facts at the technological application

. Small kerfes, minimal material loss, low pollution
  by Fine Focus plasma principle with Double straight effect.
. Excellent cutting quality at both cutting surfaces.
. No run-on cuts necessary.
. Optional application of water cooled machine or hand torches.
. Pre-selection of plasma gases and plasma gas mixtures
  Ar/H2/N2, Ar/H2, Ar/N2, air and O2 for best cutting quality
  at different materials.
. High-voltage ignition for pilot arc start.

Large variety of application

. Hose bunch lengths up to 25 m possible, for
  CNC controlled application with Hf-screening.
. On customer's request special torch models are
  available - 60° and 90°, short shank, etc.

Low operating costs

. Through a direct and extremely effective water cooling
  of the spare parts an up to five times higher life time
  of nozzles and cathodes can be achieved.
. Soft start circuit increases the life time
  of nozzles and cathodes in addition.
. XL-Life-Time system for the plasma gas O2.

High labour safety

. High labour safety through shock-proof with safety
  shut-down at cutting withhand torches and key-operated
  switch to avoid inadmissible starting.
. Control of the plasma gas, the thermal cycle and the
  thermal load of theplasma cutting system.

Plasma cutting and plasma gouging - two technologies
with only one machine

. Plasma gouging for preparation of welding seams,
  crack and inclusion removal, cast iron cleaning,
  surface removal and more, preferably with the plasma
  cuttingsystems PA-S30 WH, PA-S40 WH, PA-S25 W and PA-S45 W.

. Kjellberg plasma torches PB-S25 WH and PB-S45 WH can be
  reset from the version for plasma cutting to the application for
  plasma gouging and vice versa in a few seconds.

. There need to be replaced nozzle and protection cap only.
  With this concept a high availability of the system is
  guaranteed.The hose bunch lengths of the plasma torches
  come to 6 m or 10 m in series.The excellent ignition character
  of the plasma arc allows the use of optional
  up to 25 m hose bunches for the plasma torches.

Compared to gouging with carbon electrodes, a host of
technological advantages result, i.e.:

-no effected zone of the material.
-no grinding.
-lower heat penetration and therefore lower warpage.
-good observation of the process performance.
-noise level and smoke accumulation reduction.
-Mild steels are favourably treated with air as plasma gas.
-for high alloyedsteels and aluminium are Ar/H2/N2/
 mixtures to be used.

Technical data:

Mains voltage (V)		3 x 230 / 400 50 Hz
Fuse, slow (A)		50 / 35
Connecting power (kVA)		22 / 16
Protection class		IP 22
Insulation class		F
Open-circuit voltage max. (V)		330
Cutting current (A)		25 / 45 / 70
Cutting current (A) at d. c. 75 % 100 %		70 45
Material thickness (mm) max. cut quality cut		25 (material depending) 18 (material depending)
Plasma gases		Air, O2, Ar/H2, Ar/H2/N2, Ar/N2
Cooling		Water
Ignition		High voltage
Weight (kg)		168
Dimensions L x W x H (mm)		950 x 410 x 950

• EN 60974-1, VDE 0544, EN 50078, EN 50192, EN 50199, VBG 15 (UVV 26.0)
• CE sign, manufactured according to DIN EN ISO 9001
• S sign, applicable to welding jobs at work places with increased electrical endangerment