. Suitable for straight, profile and bevel cutting of up to 60°, cutting in
  all positions, for piercing, for hole cutting, for gouging, cutting
  without run-on cuts, piercing without run-on cuts.

Positive facts at the technological application

. Small kerfes, minimal material loss, low pollution by Fine Focus
  plasma principle with Double-Straight effect.
. Excellent cutting quality at both cutting surfaces.
. No run-on cuts necessary.
. Optional application of water cooled machine or hand torches.
. Pre-selection of plasma gases and plasma gas mixtures
. Ar/H2/N2, Ar/H2, Ar/N2, air and O2 for best cutting quality at
  different materials. High-voltage ignition for pilot arc start.

Large variety of application

. Hose bunch lengths up to 25 m possible, for CNC
  controlled application with Hf-screening.
. On customer's request special torch models are available -
  60° and 90°, short shank, etc.

Low operating costs

. Through a direct and extremely effective water cooling of
  the spare parts an up to five times higher life time of nozzles and
  cathodes can be achieved.
. Soft start circuit increases the life time of nozzles and cathodes
  in addition. XL-Life-
  Time system for the plasma gas O2.

High labour safety

. High labour safety through shock-proof with safety shut-down
  at cutting with hand torches and key-operated switch to avoid
  inadmissible starting.
. Control of the plasma gas, the thermal cycle
  and the thermal load of the plasma cutting system.

Plasma cutting and plasma gouging - two technologies
with only one machine

. Plasma gouging for preparation of welding seams, crack and
  inclusion removal, cast iron cleaning, surface removal and more,
  preferably with the plasma cutting systems PA-S30 WH,
  PA-S40 WH, PA-S25 W and PA-S45 W.

. Kjellberg plasma torches PB-S25 WH and PB-S45 WH can be
  reset from the version for plasma cutting to the application for
  plasma gouging and vice versa in a few seconds.

. There need to be replaced nozzle and protection cap only.
. With this concept a high availability of the system is guaranteed.
. The hose bunch lengths of the plasma torches come to 6 m or
  10 m in series.
. The excellent ignition character of the plasma
  arc allows the use of optionalup to 25 m hose bunches
  for the plasma torches.

Compared to gouging with carbon electrodes, a host of
technological advantages result, i.e.:

. no effected zone of the material.

. no grinding.

. lower heat penetration and therefore lower warpage.

. good observation of the process performance.

. noise level and smoke accumulation reduction.

. Mild steels are favourably treated with air as plasma gas.
  For high alloyed steels and aluminium are Ar/H2/N2/ mixtures
  to be used.

Technical data:

 

Mains voltage (V)		3 x 230 / 400 50 Hz
Fuse, slow (A)		100 / 63
Connecting power (kVA)		42 / 30
Protection class		IP 22
Insulation class		F
Open-circuit voltage max. (V)		370
Cutting current (A)		45 / 85 / 130
Cutting current (A) at d. c. 60 % 100 %		130 85
Material thickness (mm)   max. cut                                          quality cut		45 (material depending) 35 (material depending)
Plasma gases		Air, O2, Ar/H2, Ar/H2/N2, Ar/N2
Cooling		Water
Ignition		High voltage
Weight (kg)		240
Dimensions L x W x H (mm)		950 x 710 x 1,020

• EN 60974-1, VDE 0544, EN 50078, EN 50192, EN 50199, VBG 15 (UVV 26.0)
• CE sign, manufactured according to DIN EN ISO 9001
• S sign, applicable to welding jobs at work places with increased electrical endangerment

Kjellberg plasma solutions